Pro Dealer

1988 Ford Bronco

Saskatoon, Saskatchewan

$34,010

Vehicle Details

Make

Ford

Model

Bronco

Year

1988

Mileage

150,993 miles

Body Type

SUV

Transmission

Automatic

Drivetrain

4WD

Fuel Type

Gasoline

Engine

5L V8

Description

Price: US $34,010 (CAD $47,990 at the dealer).

1988 Ford Bronco Eddie Bauer 4X4. This has to be the nicest Bronco anywhere! Fully restored from top to bottom. Despite having 243,000 kms on the original drivetrain, the mechanicals, body and interior are all sorted out right back to new! The truck was sold new at Metro Ford in Calgary and has lived its entire life in Alberta.

Extensive paperwork comes with the truck outlining all the recent mechanical and cosmetic repairs. All fluids are new and anything required to make the truck 100% roadworthy has been completed. Work includes a new power steering box, new rear diff pinion seal, new steering pump and fluid, reseal and recharge of the A/C system, new heater core, new water pump, rad hoses and fluid, wheel alignment, new tire rods, new 4X4 hub seals, new Magna flow exhaust, new battery, new starter solenoid, new engine timing cover gasket, new front grille and bumper, new window motor, new window felts and rubbers and much more if you want to sit down and read through the stack of receipts! Thousands of dollars have been spent on the restoration of the truck including the required body work (just minor repairs on the fenders) and beautiful paint job in base/clear in the original Eddie Bauer two-tone green and tan.

New decals, pinstriping, trim and mouldings were sourced as necessary. No matter what angle you look at the truck from, it’s sensationally well done. The underside has very little scaling anywhere, and the floors are perfect.

The quality of restoration is extremely high on this one with extensive attention to detail, even in areas like the rocker panels and inner fenders. Paint quality is beautiful. The paint is glossy, smooth and clearly was wet sanded in the finishing stages.

A section of paint protection film was also added to the leading edge of the hood to prevent stone chips. Wheels were finished back to new and powder coated. Even the stainless-steel panel on the rear tailgate looks like it just left the factory.

You get a sense when you get up close to the Bronco just how much attention was paid to the little details. This a totally loaded Bronco! Power windows, power locks, A/C (still blows cold), tilt steering, cruise control, power rear window and AM/FM cassette and full gauge cluster with tachometer round up the luxury features. Being an Eddie Bauer edition, you also get special captains chairs with dual arm rests on each and Eddie Bauer stitching.

In between the buckets is a console and the dash features simulated wood trim. Wall to wall carpeting, upgraded door panels and the special interior and exterior colors are all part of the Eddie package. The headliner matches the interior and is still perfect.

The seats are in excellent condition with only minor wear on the driver’s seat. Carpets have no wear and are extremely clean. The dash is crack free, and all functions and options on the truck are in working order.

The owner’s manual package is still complete and in the glove box. We love that a 90’s vintage set of aftermarket mats come with the truck – the Tasmanian Devil Bugs, Daffy, Road Runner and the Coyote all on the floor mats. The swing away spare tire holder has all been restored and powder coated, the power retractable window works and drop the tailgate to reveal the fully carpeted rear trunk area with working light and no scratches anywhere on the trunk plastics – which is incredible for a car that was designed to be a utility vehicle.

Most of these were pretty used up over the years. Under the hood is the original fuel injected 5.0-liter V8 with the original 3-speed automatic behind that. As mentioned before all the tune-up and maintenance work required has been completed on the powertrain.

Power routes through a rebuilt transfer case and then through the serviced but original front and rear axles. 4X4 controls are shifted on the floor manually with both high and low range gears and the whole system is in working order. Bottom line, a large amount of money, time and effort has been spent bringing this Bronco right back to like new, original as it left the factory, condition. The color scheme is fantastic, the unit is absolutely loaded, and you won’t find a nicer one anywhere around.

The higher milage doesn’t mean much when everything has been done properly over the years. If you’re looking for a time-machine back to 1988, look no further!

Classic Ford Bronco Buyer's Guide

Full guide

Tom Ramirez

Corvette

1966–1996

~6 min read

Updated Apr 2026

Definitive buyer's guide for classic Ford Bronco 1966-1996. Early Bronco 1966-1977 and Big Bronco 1978-1996 generations, frame and tub rust, 289/302 V8 identification, current market pricing.

This guide covers

✓ 10-point inspection checklist

✓ Common issues & what to avoid

✓ In-person inspection guide

✓ Market pricing by year & condition

✓ 5 FAQs answered

✓ History & fun facts

Read the Full Bronco Buyer's Guide

Ford Bronco Market Overview

Based on 97 Ford Bronco listings currently on ClassicCarsArena.com

Listed Now

$60,767

Avg. Asking Price

1966–1996

Year Range

Price Position on Our Site - Average Range

This car: $34,010

Low: $5,000 High: $274,995

Transmission Distribution

Automatic 59% ◄

Manual 32%

Condition Distribution

Excellent 18%

Good 11%

Fair 2%

Data from ClassicCarsArena.com listings Browse all 97 listings →

💰

What is this car worth?

Check asking prices for the 1988 Ford Bronco

Valuation Tool →

🔑

Selling a classic? Here's how

Fees, audience and photo limits compared: the best sites to sell a classic car .

List Yours →

Classic Ford Bronco Buyer's Guide

The Ford Bronco has lived through five distinct platform generations across thirty years of production, but the classic Bronco market splits cleanly into two eras: the "Early Bronco" (1966-1977) and the "Big Bronco" (1978-1996). The first generation has become the single fastest-appreciating American collector vehicle of the past decade, with documented original examples now trading for sums that rival muscle-car territory. I've spent two decades chronicling Ford's SUV history, and the build sheet tells the real story on every Bronco, what was originally optional, what was dealer-installed, and what has been added during the car's lifetime. This guide covers what separates a documented original Early Bronco from a creative "restomod" build sold as factory-original.

What to Check Before Buying

✓

Order Marti Report for any 1967+ Bronco over $30K , Marti Auto Works $25. Confirms original engine, transmission, axle, paint, options, dealer destination.

✓

Cross-reference against Bronco Driver registry , Marque registry maintains records of known-original and known-restored cars. Identifies modifications.

✓

Inspect frame body mount points (Early Broncos) , Six per side. Probe with screwdriver. Solid steel resists; rotten metal flakes. Replacement = $8,000-$18,000.

✓

Examine rear frame cross-member , Common rust point on Early Broncos. Critical for trailer towing capacity and chassis integrity.

✓

Lift rubber mats and check floor pans , Both driver and passenger sides, front and rear. Universal rust point on Early Broncos.

✓

Verify uncut tub vs cut-and-modified , Original sheet metal has factory spot welds and seams. Modified sheet metal has hand-welded joints. Uncut tubs add 25-50% premium.

✓

Cross-reference VIN engine code with block casting , 8th digit of VIN (1968+) = engine code. Block casting numbers verify Windsor 289/302 originality.

✓

Verify Dana axle casting numbers , Dana 30 (1966-1971) and Dana 44 (1972-1977) front axles. Original units add value when verified factory-installed.

✓

Check rear cargo area floor (Early Broncos) , Lift rear seat or storage compartment. Common rust point invisible from outside.

✓

Test all electrical and 4WD engagement , Hubs, transfer case, and 4WD selector should engage cleanly. Failed components on Big Bronco era cost real money to repair.

Common Issues

Early Bronco rust is the structural killer for any 1966-1977 Bronco that lived in salt-belt climates. The frame rusts at the body mount points and the rear cross-member; the body tub rusts at the rocker panels, the floor pans (especially the rear cargo area floor), the lower fenders behind the front wheels, the tailgate hinges, and the cowl seam where the windshield base meets the firewall. Cars described as "uncut, rust-free" with original tubs are increasingly rare and command significant premium pricing. Mechanically, the Early Bronco's engine options are simple. The 170 inline-six (1966-1969), 200 inline-six (1970-1977), 289 V8 (1966-1968), and 302 V8 (1969-1977) are all bulletproof when maintained. The Dana 30 front axle (1966-1971) and Dana 44 front axle (1972-1977) are robust; the Ford 9-inch rear axle is essentially indestructible. The Toploader 3-speed manual transmission is durable; the C4 automatic (1973+) is similarly reliable. Common issues include worn kingpins on Dana 30 axles, leaking transfer case seals, and tired carburetor settings. Big Bronco (1978-1996) issues are different. The 1978-1979 Big Broncos used the Bronco-specific frame; 1980+ Big Broncos shared the F-150 platform. Rust patterns shifted to the rear quarter panels, the cab corners (lower section behind the rear doors), the rear wheel arches, and the tailgate. Mechanically, the 351M, 400, 460, 302, 351W, and 5.8L V8 engines are all robust. Common issues include failed fuel pumps (1980-1989 cars used in-tank pumps that fail expensively), TFI ignition modules, and worn front axle u-joints. Electrical issues vary by generation. Early Broncos have brittle 50+ year-old wiring; Big Broncos have more sophisticated electrical systems prone to module failures.

What to Look For

Marti Auto Works build sheets are the gold-standard documentation for any 1967-and-later Bronco. The build sheet ($25 for basic, more for elite reports) confirms the original equipment of the car: engine code, transmission code, axle ratio, paint code, options, and dealer destination. For any Early Bronco priced over $30,000, the Marti Report is mandatory, too many cars on the market wear emblems and equipment that wasn't original to the car. Frame inspection is the first non-negotiable for Early Broncos. The frame rusts at the body mount points (six per side on Early Broncos) and at the rear cross-member. Lift the body off the frame with a flashlight and probe rusty areas with a screwdriver. Solid steel resists; rotten metal flakes. Frame replacement is a serious undertaking, $8,000-$18,000 for proper professional work. Tub inspection is the second non-negotiable. The Early Bronco body tub is a single welded steel structure that becomes increasingly difficult to repair properly as rust progresses. Inspect the floor pans (lift the rubber mats), the rocker panels (under the doors), the rear cargo area floor (lift the rear seat or storage compartment), the cab corners, and the tailgate hinge area. Cars described as "uncut tubs" with original sheet metal are the gold standard. Engine and drivetrain verification: cross-reference the VIN engine code (eighth digit, on 1968+ cars) with the engine block casting number. The Early Bronco 289 (1966-1968) and 302 (1969-1977) Windsor V8s have specific casting numbers that verify originality. The 170 and 200 inline-sixes are similarly identifiable. Original Dana axles have specific casting numbers and stampings that verify factory installation. Document the build sheet against the car. Cross-reference against the marque registry, the Bronco Driver registry maintains records of known-original cars and known-restored cars. The build sheet tells the real story.

Price Guide

Early Bronco (1966-1977) values have appreciated dramatically over the past decade. Driver-quality 1966-1969 cars (the original 'short' Bronco) run $45,000-$80,000 today. 1970-1977 cars run $35,000-$70,000 in driver condition. Documented original-paint, low-mileage examples can reach $95,000-$150,000+. Documented uncut original tubs in survivor condition are the ultimate Early Bronco, these cars trade for $80,000-$220,000 depending on year, condition, and equipment. The 1966 launch year cars are the most desirable, with documented original 1966 cars approaching $200,000+ when fully verified. LS-swapped restomod Early Broncos (with modern drivetrains, modern brakes, modern interior) run $80,000-$220,000 depending on quality of build. Frame-up restomod builds from recognized specialists (Gateway, Velocity, Maxlider, Icon) run $200,000-$500,000+. Big Bronco (1978-1996) pricing is dramatically more affordable. Driver-quality 1978-1979 cars run $22,000-$42,000. 1980-1989 cars run $15,000-$32,000. 1990-1996 cars run $12,000-$28,000. The 1990s OJ Simpson-era white Broncos have appreciated due to pop-culture interest, clean white 1990-1996 Broncos run $22,000-$45,000. Project Early Broncos (running but rough) start around $15,000-$28,000. Stripped roller candidates can be had for $8,000-$20,000, but rust restoration on a Bronco typically runs $30,000-$70,000 in body and frame work alone before paint.

Did You Know?

The 1966 Ford Bronco was developed under chief engineer Paul Axelrad as a direct response to the original Jeep CJ. Ford Product Planning identified an unmet market for a compact, capable, on-road-and-off-road vehicle that would appeal to suburban families as well as serious off-roaders. The original concept was approved by Lee Iacocca (then Vice President of Ford Motor Company) in 1963, and the car launched in August 1965 as a 1966 model. Only 4,090 Roadster variants (Bronco model U13) were built in 1966, making them among the rarest Early Bronco variants. The U13 Roadster had no roof and no doors. The Half-Cab Pickup was a separate body style (model U14) with a fixed forward roof and open rear cargo bed. Documented Roadster examples in survivor condition trade for $80,000-$150,000+ today. The Bronco was discontinued in 1996 after 30 years of continuous production, replaced by the four-door Ford Expedition for the 1997 model year. Ford reintroduced the Bronco nameplate for the 2021 model year on an entirely new platform, but the 1966-1996 classic Broncos remain a separate market segment with no direct connection to the new vehicles. I've spent two decades chronicling Ford's SUV history, and the original Bronco's combination of compact dimensions, rugged engineering, and timeless styling explain why these cars have become the fastest-appreciating American collector vehicles of the past decade.